dd-wrt の公式ウェブサイトの wds の設定方法は次のところにあります。しかしよく解りませんでした（汗）。 dd-wrt には数多くのバージョンが存在することもあって、その他の wds の設定について紹介しているブログを幾つか参考にしながら、以下の方法で wds 接続に成功しました。
DD-WRT has been impressing users since its inception in 2005, and is the go-to alternative router firmware due to its longevity of existence and support of the largest array of devices. Consequently, DD-WRT can claim the largest community of users. It's the backbone of what we do here at FlashRouters. A Wireless Distribution System, or WDS, is a cheap and easy way to extend your wireless network coverage. It’s cheap, because you can set up a couple of sub-$60 routers with the open-source firmware DD-WRT , including the Linux-powered Linksys WRT54GL (only $56 these days on Amazon.com ) and other compatible routers. Second issue is the real issue- When using WDS AP and WDS STA mode along with a UL/LU channel, the STA will only connect at HT20 speed. (Clarification still necessary if only on 2.4ghz, 5ghz or both). UU and LL in WDS AP and WDS STA mode works fine from what I read at the top. This is a bug for sure and I agree. A wireless distribution system (WDS) is a system enabling the wireless bridging of access points in an IEEE 802 network. It allows an extended network to be created using wireless IEEE 802.11 access points without the traditional requirement for wires to link them. More recently many routers running the dd-wrt or tomato based router OS have supported something know as Wireless Distribution System (WDS). WDS - also called Repeater-Bridge mode allows you install multiple WiFi routers in your home. You configure a "primary" router like you would normally and then 2 or more routers as WDS Bridge routers.
May 06, 2020 · Head to the DD-WRT database, then type in the exact model number of your router. This database will tell you your router is one of four things: Supported, which means you can install DD-WRT. This
A Wireless Distribution System, or WDS, is a cheap and easy way to extend your wireless network coverage. It’s cheap, because you can set up a couple of sub-$60 routers with the open-source firmware DD-WRT , including the Linux-powered Linksys WRT54GL (only $56 these days on Amazon.com ) and other compatible routers. Second issue is the real issue- When using WDS AP and WDS STA mode along with a UL/LU channel, the STA will only connect at HT20 speed. (Clarification still necessary if only on 2.4ghz, 5ghz or both). UU and LL in WDS AP and WDS STA mode works fine from what I read at the top. This is a bug for sure and I agree. A wireless distribution system (WDS) is a system enabling the wireless bridging of access points in an IEEE 802 network. It allows an extended network to be created using wireless IEEE 802.11 access points without the traditional requirement for wires to link them. More recently many routers running the dd-wrt or tomato based router OS have supported something know as Wireless Distribution System (WDS). WDS - also called Repeater-Bridge mode allows you install multiple WiFi routers in your home. You configure a "primary" router like you would normally and then 2 or more routers as WDS Bridge routers.
Category Wireless, WiFi-Repeater Manufacturer Linksys Linksys E900 802.11n 300Mbit wireless router compact with 2 integrated antennas. Optional with DD-WRT in WDS mode, multi repeater Linksys E900 300Mbit WiFi Router, option DD-WRT WDS 5-Port Switch
Install and Configure a DD-WRT Kong Router: DD-WRT is a wonderful open source custom router firmware that is supported on many devices. It adds features, stability and configurability to consumer routers.However, it's not easy for a novice starting out with DD-WRT. DD-WRT is a Linux-based firmware project developed to enhance the performance and features of wireless Internet routers. Launched in 2005, DD-WRT is one of the most popular alternative router firmwares due to its longevity of existence and support for a large array of devices. My intention was to try out and report on the DD-WRT software project. Both the WRT54G and the WRT54GL are supposed to work with DD-WRT, however, their may be issues with WRT54G. The following documents the trouble free flashing steps I followed to install DD-WRT on a WRT54GL router. Presumably, the L stands for Linux. - *.bin files can only be flashed from dd-wrt webif. - *.chk can be flashed from Netgear factory fw and from dd-wrt webif - I don't provide factory to dd-wrt for non Netgear models since I do not own any non Netgear Broadcom units. All builds include ddup util, which allows update checking and flashing of the following models: Netgear EX6200 These are the features available in the Standard version of DD-WRT. Other versions, such as the Micro or Mini, may lack some specific features to lower the package size. This list uses content from the WRT Wiki article "What is DD-WRT" as retrieved on September 24, 2006 , which is licensed under the GNU Free Documentation License 1.2 .